Mounting Solar Modules and Estimating Parts

Some of the most important questions for most installers and DIY solar enthusiasts concern mounting solar panels. There are many high quality mounting solutions on the market such Unirac, IronRidge, PowerFab, Quickmount PV, Schletter etc. By way of example, we'll go over the materials required for a given application using the Unirac SolarMount racking system.

 A simple roof mounting system may require the following items:

1. Rails (to provide a platform for mounting the modules)
2. Splices (to connect rails as needed)
3. Mid clamps (to be located between each module)
4. End clamps (to secure the end of last module)
5. L-feet or standoff (to secure the rail to the roof)
6. Flashing (to prevent water leakage)
7. Grounding lugs (to run the grounding wire)
8. Grounding clips (to create grounding paths for modules through rails)

A helpful resource can be found in the Unirac Master Component List, which contains product numbers that can be useful when compiling the bill of materials.

1) Estimating the Rail Size (Unirac Master List page 12)

To begin you will need to know how many modules will be placed in each row. You should also determine the dimensions of each module and the orientation of the panels (portrait or landscape). Please refer to the nine modules oriented in portrait as seen on the second picture. (Click the second sliding dot under the page above.) 

To estimate total rail size, simply multiply the module width (if in portrait, or the module length if in landscape) by the number of modules in a row. Then add one inch between each module and two inches at each end of the modules for the mid and end clamps, respectively.

In the present case, installing nine 31.4 inch modules in one row, I need 282.6 inches of rail. Adding eight inches for mid clamps and two inches for end clamps results in a minimum of 294.6 inches of rail. 

Going back to the Unirac Master Component List, you can see that rails come in predetermined lengths. I will connect two smaller rails to create the needed length via a splice (See Splices in section 2). The 156 inch SolarMount rail (part number 300011) is my best bet.

Each row of modules requires two rails (top and bottom). This system, which has two rows of modules, requires four rails. Further, since I will be splicing two 156" rails in order to reach the required 294.6" rail length, I will need a total of eight 156" rails.

2) Splices (Unirac Master List page 16)

In order to connect two 156" rails (to achieve the total required length), I need to use one splice splice bar. I need a total of four splice bars (one for each splice point between eight rails).

3) Mid Clamps (Unirac Master List page 20)

The number of end clamps required is equal to one less than the number of modules on each row. For nine modules, I need eight mid clamps for each rail. As I have four rails, I need 32 mid clamps.

The thickness of the module is also important here. Since the module thickness that I use is 1.82", I use F type mid and end clamps which are applicable for modules between 1.77" to 1.85". Please refer to Unirac Master List pages 6 to 8 or pages 20 to 22 to determine the size you will need to use.

Note: You may prefer to use bottom mounting clips instead of mid and end clamps. Bottom clips are cheaper, but more difficult to install in large systems.

4) End clamps (Unirac master list page 20)

Four are required for each row as end clamps are going to be attached to the ends of each rail. In my case, I need eight end clamps for the rows in this array.

5) L-feet or standoffs (Unirac master list page 44-45)

L-feet and standoffs are the parts that connect your rail to the roof. The number of L-feet depends on how sturdy of a system you need. In conditions where there is not significant snow load or high wind speed, L-feet spacing of 5 ft or close can be necessary. The harsher the conditions, the more L-feet connections and roof penetrations are required. In order to keep roof penetrations to a minimum, heavy duty rails are available which allow for longer spans.

For my system I am using a 5 ft rail span necessitating at least six L-feet for every 294 inch length of rail. As I have four rails, I need 24 L-feet for my system.

If you prefer to use standoffs instead of L-feet, the same calculation is required.

6) Flashings

The number of flashings needed is generally equal to the number of L-feet/standoffs required. In the specified L-feet system, I prefer to use QuickMount PV flashing solutions. It's likley best to use Unirac flashing with Unirac standoffs.

7) Grounding Clips (Unirac Master list page 17)

Order one grounding clip for every two top mounting clamps (mid plus end clamps). Only one of the two rails in each array row requires grounding clips. 

I need 32 mid clamps and 8 end clamps for my system. Thus, I need 20 (40/2) grounding clips for my system (two 10 packs of item number 980005).

8) Grounding Lugs (Unirac Master list page 17)

Order one lug for each span of rail and two for each rail splice. Since I need two grounding lugs for each splice that I have in my system and I have four splices on four rows, I will need a total of 12 grounding lugs. Grounding lugs come in packs of ten, so I will order two packages of part number 980011.

Once you know the part numbers that you need, the best way to go about acquiring such products is to contact a distributor and ask for a quote. You can create your own quote at Greentech Renewables by searching for the related parts. Please see the above pictures to view the previously specified parts.